Select a different country or region to see content for your location.
United States
13:41:05 GMT+0000 (Coordinated Universal Time)
LTS30-180-TR20x4-M-0
Linear table
Frequently bought together
Main Dimensions & Performance Data
| H | 77 mm | Total Height |
| B1 | 180 mm | Total Width |
| L | 180 mm | Length of carriage |
Mounting dimensions
| D7 | 30 mm | Tolerance h7 |
| D8 | 9 mm | |
| H1 | 60 mm | Height of carriage |
| H12 | 16 mm | |
| JB43 | 158 mm | |
| jB8 | 51 mm | |
| jL8 | 150 mm | |
| K43 | M10 | |
| Ltot | 2.900 mm | Maximum length |
| Rx | 98,6 mm | |
| S | 4 mm | Safety distance |
| S | 15 mm | |
| T8 | 7,5 mm | |
| T86 | 2,8 mm | Depth Fit |
| t43 | 26 mm | Depth of Thread |
| t87 | 15 mm | Depth of Thread |
| b87 | 68 mm | Tolerance ±0,2 |
| d85 | 10 mm | Diameter drive shaft, Tolerance h7 1 |
| D86 | 32 mm | Tolerance H7 |
| G4 | M12 | Thread |
| G5 | M12 | Thread |
| G87 | M6 | Thread |
| G43 | M12 | Thread |
| h5 | 29 mm | |
| h85 | 42 mm | |
| h87 | 44 mm | Tolerance ±0,2 |
| JL43 | 158 mm | |
| jB4 | 150 mm | |
| JL4 | 12,5 mm |
Dimensions
| H7 | 7 mm | |
| h1 | 35 mm | |
| L4 | 38 mm | Length of Shaft Support Block with Drive System |
| L5 | 25 mm | Length of Shaft Support Block without drive System |
| L88 | 36,5 mm | |
| L86 | 9,4 mm | |
| Rz | 96 mm | |
| H5 | 58 mm | Height of Shaft Support Blocks |
Technical data
| vmax | 0,1 m/s | Maximum Speed |
| amax | 2,5 m/s2 | Maximum Acceleration |
| d0 | 20 mm | Spindle Diameter |
| P | 4 mm | Spindle Pitch |
| mLAW | 4,3 kg | Mass of Carriage |
| Is | 0,81 kg*cm2 | Mass moment of inertia of threaded Spindle |
| CI | 9.760 N | Load direction I: compressive load |
| C0I | 12.000 N | Load direction I: compressive load |
| CII | 5.930 N | Load direction II: tensile load |
| C0II | 7.600 N | Load direction II: tensile load |
| CIII | 8.970 N | Load direction III: lateral load |
| C0III | 10.700 N | Load direction III: lateral load 2 |
| C0 | 2.550 N | Load capacity Spindle Nut stat 3 |
| C0a | 2.550 N | Load capacity fixed Spindle bearing stat |
| M0x | 340 Nm | Max. permissible static moment per Carriage 3 |
| M0y | 450 Nm | Max. permissible static moment per Carriage 3 |
| M0z | 345 Nm | Max. permissible static moment per Carriage 3 |
Additional information
10 Nm | Max. permissible drive torque | |
2x7201-2RS | Rolling Bearings | |
0,81 kg*cm2 | Mass moment of inertia of threaded Spindle | |
KBO30-PP-AS | Bearing 2 |
Temperature range
| min | 0 °C | Minimum operating Temperatur |
| max | 80 °C | Maximum operating Temperatur |
Footnotes
1
Thread witness marks may be present on the pin.
2
Design of linear ball bearing guidance systems: see Catalogue WF1, Shaft Guidance Systems.
3
These values apply if load is evenly distributed over all four linear ball bearings. The values are single loads and apply when the shaft and support rail units are fully supported. These must be reduced for combined loads. For design criteria of the linear guidance system, see Catalogue WF1, Shaft Guidance Systems.
Downloads:
Your current product variant
| Size code | 30 | |
| Drive type | TGT | Trapezoidal screw drive |
| Length of carriage | 180 | 180 mm |
| Spindle diameter | 20 | 20mm |
| Spindle pitch | 04 | 4 mm |
| Spindle nut design | M | Cylinder nut |
| Bellow | 0 | No |
